6.4 Mechanical Engineering Program Regulations

On this page

6.4.1 Mechanical Engineering Major
6.4.1.1 Technical Electives

6.4.1 Mechanical Engineering Major

The full-time 141 credit hour Bachelor of Engineering (Co-operative), Mechanical Engineering Major, requires eight academic terms and four work terms.
The 141 credit hours shall normally be taken in the academic terms and order as set out in Mechanical Engineering Major.
Work terms shall normally be taken in the order as set out in Mechanical Engineering Major.

Mechanical Engineering Major
Term	Required Courses	Elective Courses
Engineering One	Chemistry 1050 or 1200 ENGI 1010, 1020, 1030, 1050 (or the former ENGI 1040) 3 credit hours in English at the 1000 level or any Critical Reading and Writing course Mathematics 1000, 1001, 2050 Physics 1050, 1051	Students who are expecting to successfully complete the Engineering One requirements by the end of the Winter semester may apply to undertake a work term during the Spring semester. In this case, the prerequisite course ENGI 200W is expected to be successfully completed during the Fall semester. All other students are expected to successfully complete ENGI 200W in the Winter semester of Engineering One.
In addition to meeting the requirements outlined below, a student must successfully complete four Complementary Studies courses as described under Description of Program, Complementary Studies.
Fall Academic Term 3	ENGI 3101, 3424 ME 3101, 3102, 3301, 3401
Winter	ENGI 001W or 002W
Spring Academic Term 4	ENGI 4430 ME 4302, 4402, 4501, 4601
Fall	ENGI 001W or 002W or 003W
Winter Academic Term 5	ENGI 4421 ME 5103, 5201, 5502, 5602
Spring	ENGI 002W or 003W or 004W
Fall Academic Term 6	ME 6202, 6303, 6403, 6701, 6702
Winter	ENGI 003W or 004W or 005W (optional)
Spring Academic Term 7	ME 7203, 7703, 7704	6 credit hours chosen from the table of electives, or otherwise meeting the requirements in, Technical Electives One free elective which must be a 2000-level or higher course from any academic unit. Course selection must be approved by the Head of the Department of Mechanical and Mechatronics Engineering and must be completed before Academic Term 8.
Fall	ENGI 004W or 005W (optional) or 006W (optional)
Winter Academic Term 8	ENGI 8152 ME 8705	9 credit hours chosen from the table of electives, or otherwise meeting the requirements in, Technical Electives

6.4.1.1 Technical Electives

During Terms 7 and 8, students must choose a total of at least three (3) Group A Technical Electives from the table below, with any remaining Technical Electives from Group B. Other courses may be offered or approved by the Head of the Department of Mechanical and Mechatronics Engineering and designated as Group A or B.
Courses not listed in the table below, such as those from other departments, may only be taken with the approval of the Head of the Department of Mechanical and Mechatronics Engineering.

Technical Elective Courses
Group A Courses	Group B Courses
Term 7 ME 7104, ME 7205, ME 7404, ME 7405, ME 7603	Term 7 ME 7105, ME 7204, ME 7210, ME 7220, ME 7230, ME 7503, Electrical and Computer Engineering 7200, Electrical and Computer Engineering 7410, Process Engineering 7171
Term 8 ME 8304, ME 8305, ME 8406, ME 8407, ME 8504, ME 8604	Term 8 ME 8106, ME 8505, ME 8506, ME 8605, ME 8606, ME 8801, Civil Engineering 8580, Electrical and Computer Engineering 8410, Electrical and Computer Engineering 8610, Engineering 8153, Engineering 8158, Process Engineering 8170, Process Engineering 8292

The information on this site has been extracted from the Official 2024-2025 University Calendar. While every reasonable effort has been made to duplicate the information contained in the official University Calendar, if there are differences, the official Memorial University of Newfoundland Calendar will be considered the final and accurate authority.